top of page
Custom Aluminum Nitride (AlN) Ceramic Substrates & Submounts

Custom Aluminum Nitride (AlN) Ceramic Substrates & Submounts

Aluminum nitride (AlN) ceramic substrates combine high thermal conductivity with electrical insulation for demanding thermal-management and electronic packaging applications. Microns Advanced Ceramics supports AlN material selection and custom component enquiries based on application requirements, grade, dimensions, and drawing specifications. Engineering review from Hayward, CA (30995 Santana St, Hayward, CA 94544).   

Request Substrate Quote & DFM Review →   


AlN Product Forms

  • AlN Ceramic Substrates: Flat sintered blanks and cut parts to drawing.

  • AlN Wafers: Sintered polycrystalline (not single-crystal AlN wafers).

  • AlN Submounts: Laser diode and LED submounts.

  • AlN Thermal Pads: Heat spreaders and heatsinks.

  • AlN PCB Components: Metallized circuit substrates.

  • Custom Machined Parts: Rings, sleeves, and heaters to drawing.


Standard & Custom Dimensions

  • 2" × 2" (50.8 × 50.8 mm): Thicknesses 0.127, 0.254, 0.38, 0.5, 0.635, 1.0 mm

  • 4" × 4" (101.6 × 101.6 mm): Custom thickness to specification

  • 4.5" × 4.5" (114.3 × 114.3 mm): Custom thickness to specification

  • Minimum thickness: 0.05 mm (coupled with part area; camber and handling risk rise as thickness drops)

  • Hole / diameter tolerance: Ø0.005 mm

  • Flatness: 5 µm


Grade Selection & Thermal Performance

  • 170 W/m·K Class: Standard commercial sintered grade

  • 180 W/m·K Class: Up to 180 W/m·K, grade dependent

  • High Conductivity (HTC): Elevated thermal diffusivity grade (Note: Specify grade designation and measurement temperature per ASTM E1461 flash method rather than a W/m·K target alone.)


Metallization, Lapping & Precision Finishing

  • Grinding (diamond / ultrasonic): Thickness and parallelism control

  • Double-sided lapping & polishing: Lower surface roughness (Ra) for thin-film applications

  • Laser cutting & micro-via drilling: Via drilling precedes DPC plating

  • Thin film (Ti/Pt/Au, Ni/Au): Sputtered, photolithographically patterned

  • Thick film (Ag/Pd, W/Mo): Printed and fired

  • DBC / AMB / DPC: DBC to ~1060 °C (>200 µm Cu); AMB ~800 °C; DPC 10–150 µm Cu (0.05 mm line/space)


Material Comparison: AlN vs. Alumina vs. BeO

  • Thermal Conductivity (W/m·K): AlN: 140–180 | Alumina (99.5%): 35 | BeO: 285

  • CTE (×10⁻⁶/°C): AlN: 4.5 | Alumina (99.5%): 8.4 | BeO: 7.5

  • Fracture Toughness (MPa·m½): AlN: 2.6 | Alumina (99.5%): 4.0 | BeO: Not published

  • Safety & Handling: AlN & Alumina require no beryllium exposure controls; BeO requires OSHA 29 CFR 1910.1024 compliance (PEL 0.2 µg/m³, 8-h TWA).


Applications

  • Power electronics and EV power modules

  • Semiconductor packaging

  • RF and microwave components

  • LED and laser-diode thermal management


Why Microns Advanced Ceramics

  • Hayward, CA engineering support and DFM drawing review before quoting

  • Factory-direct global manufacturing with origin stated on each quotation


Submit Your CAD-Ready RFQ To receive a fast DFM review and quote, include your Form (Wafer/Substrate, Submount, Thermal Pad, Custom Part), Grade (170 vs. 180+ W/m·K), Surface Finish (As-Fired, Lapped, Polished), Metallization, Volume, and whether you require a Mutual NDA.

  • Engineering FAQ

    • What thermal conductivity can AlN substrates reach?Commercial sintered grades span 80–180 W/m·K depending on grade and measurement temperature. The 320 W/m·K figure is a theoretical single-crystal limit.   

    • How thin can an AlN substrate be? Down to 0.1 mm for standard substrates and 0.05 mm minimum processing thickness. Thinner parts chip more easily (fracture toughness ~2.6 MPa·m½).

    • What is AlN's CTE? About 4.6 × 10⁻⁶/K over 40–400 °C, compared to 2–4 × 10⁻⁶/K for silicon. Always compare CTE over a stated temperature range.

    • Which finish and metallization do I need? The metallization route sets the surface requirement: DPC and thin film favor lapped or polished surfaces; DBC/AMB follow different thickness and flatness limits.

    • How does AlN compare to alumina and BeO? AlN offers roughly 5× alumina's thermal conductivity and ~60% of BeO's without BeO's OSHA beryllium toxicity controls, though it has lower fracture toughness than alumina.

    • What must my RFQ include? Grade and measurement condition, dimensions, thickness, surface finish, metallization route, tolerances, volume, and documentation requirements (CoA, RoHS/REACH).

0/500
bottom of page